Rethink Concrete Fiber
Next-Generation Concrete Fiber
Without the Cost of Traditional High-End Fibers
Since 2002, we have specialized in concrete crack resistance, waterproofing, and anti-corrosion technologies.
Rimix™ NanoRebar High-Performance Fiber
Next-Generation Micro Synthetic Fiber for High-Performance Concrete
What Is Rimix™ NanoRebar Concrete Fiber?
Rimix™ NanoRebar is a high-performance micro synthetic fiber made from refined polyacrylonitrile (PAN fiber), originally derived from carbon fiber precursor technology. It is designed for fiber reinforced concrete (FRC) applications, providing both early-stage crack control and long-term crack resistance.
Compared with traditional polypropylene fiber, NanoRebar offers significantly higher tensile strength and modulus, allowing it to work not only during the plastic stage, but also after concrete hardening.
By improving toughness and crack resistance, it helps reduce cracking, enhance durability, and improve overall performance in high-performance concrete (HPC) and ultra-high-performance concrete (UHPC).
Thanks to its ultra-fine diameter, NanoRebar delivers a higher fiber count at lower dosage, achieving more effective crack control with comparable overall cost to polypropylene fiber.
Next-Generation High-Performance Fiber
How NanoRebar Reinforces Concrete
Crack control in fiber reinforced concrete is governed by fiber spacing theory, proposed by Romualdi and Batson and widely referenced in ACI guidance. The theory states that crack resistance depends on reinforcement spacing: the closer the spacing, the higher the probability that cracks will be intercepted and restrained.
Rimix™ NanoRebar is designed based on this principle. Its ultra-fine PAN-based fibers provide a much higher fiber count per unit volume, resulting in closer spacing between reinforcement elements. This increases the likelihood that micro-cracks are intercepted early, reducing crack development throughout the concrete.
In addition, NanoRebar fibers have significantly higher tensile strength and elastic modulus than conventional polypropylene fiber, enabling effective crack bridging and stress transfer in both plastic and hardened stages. This results in improved crack resistance, enhanced toughness, and more reliable performance in concrete.
NanoRebar Fiber Reinforcement Inside Concrete
NanoRebar vs Polypropylene Fiber
Compared with polypropylene fiber, NanoRebar features a finer fiber diameter and provides a significantly higher fiber count per unit volume, resulting in more effective crack control. Its higher tensile strength and elastic modulus further enhance crack resistance, contributing to improved durability and overall concrete performance.
Property
Polypropylene Fiber
Rimix™ NanoRebar
Typical Fiber Diameter
20–48 μm
≈ 11 μm
Tensile Strength
300–450 MPa
600–900 MPa
Elastic Modulus
3–3.5 GPa
7–10 GPa
Recommended Dosage
0.9 kg/m³
0.45 kg/m³
Fiber Count per m³
≈ 0.6–1.0 Billion
≈ 2.7 Billion
Why Choose Rimix™ NanoRebar for High-Performance Concrete?
High-performance concrete (HPC) requires effective crack control, durability, and long-term reliability. In modern fiber reinforced concrete (FRC) systems, fiber selection plays a critical role in achieving these properties.
Traditional high-performance fibers for concrete—such as PVA fiber, basalt fiber, AR glass fiber, aramid fiber, and carbon fiber—offer excellent mechanical performance, but are often limited by high cost and restricted use in UHPC or specialized applications.
Rimix™ NanoRebar, a next-generation micro synthetic fiber for concrete based on PAN fiber technology, is designed to bridge this gap.
It delivers effective crack control, improved toughness, and reliable durability in both standard concrete and high-performance concrete fiber reinforcement systems—without the cost limitations of traditional high-end fibers.
Lower dosage, more fibers, superior performance
Benefits of Rimix™ NanoRebar
Rimix™ NanoRebar enhances concrete performance through high fiber count and distributed micro-reinforcement, offering clear advantages over conventional polypropylene fibers.
1. More Effective Crack Control
At approximately half the dosage, Rimix™ NanoRebar provides several times more reinforcement elements. This increases the probability of intercepting micro-cracks early and reduces visible cracking in slabs and structural elements.
2. Full-Stage Crack Control
With higher tensile strength and modulus, Rimix™ NanoRebar remains effective in both the plastic and hardened stages of concrete. It helps control early shrinkage cracking as well as later-stage cracking caused by loading and drying shrinkage.
3. Improved Toughness and Structural Reliability
By enabling effective crack bridging, Rimix™ NanoRebar enhances concrete toughness and reduces brittle behavior. This improves performance under impact, repeated loading, and long-term service conditions.
4. Comparable Overall Cost
Despite improved reinforcement efficiency, Rimix™ NanoRebar achieves these benefits at a comparable cost per cubic meter. Lower dosage combined with higher effectiveness makes it a practical upgrade without increasing overall project cost.
High strength and high modulus fiber for concrete reinforcement
Standards & Compliance
Rimix™ NanoRebar micro synthetic fiber meets major international standards for concrete reinforcing fiber applications:
-
ASTM C1116 – Fiber Reinforced Concrete
-
EN 14889-2 – Polymer Fibers for Concrete
Applications of Rimix™ NanoRebar
Rimix™ NanoRebar is used in fiber reinforced concrete (FRC) applications requiring effective crack control and durability.
It is suitable for both standard concrete and HPC / UHPC systems.
-
High-durability slabs, floors & pavements
-
Precast concrete elements
-
Industrial floors and heavy-traffic platforms
-
Waterproof structures: basements, tanks, pools, tunnels
-
Shotcrete for tunnels & underground work
-
Infrastructure & Marine
-
High-performance and ultra-high-performance concrete
Trusted in Engineering Projects Worldwide
How to Use Rimix™ NanoRebar
Rimix™ NanoRebar is available in multiple lengths and packaging options to suit different fiber reinforced concrete and shotcrete applications.
Lengths: 6 mm, 12 mm, 18 mm
Dosage：0.45–0.9 kg/m³
Packaging: Bulk loose fiber in ton bags or carton packaging (small packs in plastic or water-soluble bags)
Ready for Global Delivery
Upgrade to High-Performance Concrete Fiber Reinforcement
Get technical support, dosage recommendations, or a project quote today.
Looking for a Quote or More Information about Our Products?
Tell us your application and we’ll recommend the right macro or micro fiber solution for your project.
An advanced micro synthetic fiber engineered for fiber-reinforced concrete (FRC), delivering optimized performance for modern high-performance concrete applications.
-
Upgrade Your Polypropylene Fiber Today
-
Contact Rimix™ NanoRebar Expert
-
Request a Sample
-
Get a Quote
-
Become a Distributor
-
Request Technical Data Sheet
Privacy Assurance: We respect your privacy and will never share your information.
Why Choose Us?
Proven Expertise & Greater Savings
22 years of focus
on concrete protection solutions.
20+ patents & awards
In concrete durability technology
20+ countries served
with global product distribution.
1,000 projects proven
in diverse applications worldwide.
FAQ
A high-performance micro synthetic fiber made from PAN, designed to improve crack control and durability in concrete.
It has higher strength, finer diameter, and more fibers per m³—resulting in more effective crack control at similar cost.
Yes. It can directly replace PP fiber in most applications with lower dosage and better performance.
Suitable for standard concrete, HPC, and UHPC.
Typically 0.45–0.9 kg/m³, depending on application.
Contact Us
For product inquiries, OEM/ODM partnerships, or becoming a distributor: Sales@pioneerfibre.com
For technical support and application guidance: Support@pioneerfibre.com
Regional WhatsApp Support
We typically respond within 24 hours, ensuring your project continues without delays.
-
Americas: +1 (702) 307-8327
-
Europe: +86 151 6240 5106
-
Middle East & Africa：+1 (949) 317-7180
-
Asia-Pacific：+86 190 1543 5408
